search

Lyntec RPC Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel informatique Lyntec RPC. Lyntec RPC User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 2
  • Table des matières
  • MARQUE LIVRES
    • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
LynTec
RPC
Quick Start Guide
1
Make sure that the panel(s) have
been wired by a certifi ed electrician
and that there is power to the
panel(s).
Confi rm that RPS (slave) panels
are connected to the master as
indicated in the “RPC to RPS Wiring
Instructions” bulletin.
2
Confi rm that the electrician has
connected the 15A breaker in the
master panel (position 21) to the
power supply in the lower sidecar.
3
Once the 15A breaker is connected
and switched on, confi rm that the
orange power LEDs on each circuit
board are lit.
Control Board
I/O Expander
Board
Multi-Panel Expander
Board
POWER LEDS
If LEDs do not light, check chapter
4 of the RPC manual to see that
circuit boards are connected
properly.
4
Connect a computer to the control
board using a CAT5 crossover
cable OR connect the RPC to your
network.
If connecting via a crossover cable:
With a computer directly connected
to the RPC through the Ethernet
port, change the computer’s IP
address manually so it is in the same
default IP subnet that the RPC uses:
192.168.1. The default IP address of
the RPC is 192.168.1.250.
Ethernet Port
Yellow
Buttons
LCD
Screen
If connecting via a network:
Connect the RPC to the network via
the Ethernet port. Push the upper
yellow button twice or until the IP
address appears on the LCD screen.
OVER
Panel Neutral Bus
Panel Ground Bar
Power Supply DC –
Controller Cable
Controller Cable
Power Supply DC +
N L
+ + – –
Transducer Neutral
Transducer Load
15A Breaker
139-0522-00 RPC Quicksheet
Vue de la page 0
1 2

Résumé du contenu

Page 1

LynTecRPCQuick Start Guide1Make sure that the panel(s) have been wired by a certifi ed electrician and that there is power to the panel(s). Confi rm tha

Page 2

5Open a web browser and access the status page via the IP address of the RPC. (ex. http://192.168.1.250) The default username is “admin” and the ini

Plus de documents pour Matériel informatique Lyntec RPC

Voir le document Lyntec RPC Manuel d'utilisateur
Lyntec RPC Manuel d'utilisateur (57 pages)

Commentaires sur ces manuels

Pas de commentaire
Produits connexes et manuels pour Matériel informatique Lyntec RPC
Matériel informatique Lyntec RPCM Manuel d'utilisateur   (37 pages)
Matériel informatique Lyntec RPC Manuel d'utilisateur   (57 pages)
  • Elecom Best Living Systems Renault Elcell Wave Home Solutions
  • Panasonic Supports de projecteur Pioneer Platines audio Infinity Haut-parleurs pour voitures Ricoh Projecteurs de données Epson Ordinateurs portables de poche
  • Avanti WCV38DZ Acer Aspire P3-131 ViewSonic VG930m-3 Soundfreaq SFQ-02IRB Behringer TU300
  • AEG SKB41011AS Manuel de l'utilisateur Logitech UE700 Manuel de l'utilisateur Siemens A70 Manuel de l'utilisateur Electrolux EN93889MW Manuel d'installation Lg DVX392H Manuel de l'utilisateur